|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
This Acorn Soap Mold is perfect for fall soap lines! Create detailed acorn-shaped soaps and lotion bars with this plastic mold.
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC Plastic (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135ºF to145ºF. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
|
International Nomenclature of Cosmetic Ingredients (INCI):
This product does not need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved):
This product does not need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
| Average Customer Rating: |
 |
(2 Reviews) |
|
Dawn • Nevada
Date Submitted: 01/24/2023
I Recommend This Product!
|
 |
"Meh" |
|
COMMENTS: This is not my favorite mold. The shape is a little harder to get out compared to the usual plastic mold. The shape is a little odd. Design wise I think it would be better if the acorn was shorter and fatter but thats my fault. I shouldnt have bought it as the shape is exactly what is shown. I am not likely to keep this.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
|
|
Dawne • Rhode Island
Date Submitted: 09/28/2020
|
 |
"It is so hard to get the soap out of the Mold." |
|
COMMENTS: I don’t like to unmold the soap. It is so hard to get out of the mold! If you do eventually get it out of the mold the soap is beautiful but I’m not sure it’s worth using, it takes too long to remove the soap. I may just use it to make bath bombs.
|
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
4 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
