Create bars of soap for those who serve or have served in the Air Force with this plastic Air Force Soap Mold. This round bar mold has three cavities with the the detailed seal of the Air Force on each bar.

Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars. Bath Fizzies.

Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)

Milky Way Soap Molds can tolerate temperatures of 135-145 degrees F. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.

Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.

Country Of Origin: United States

Helpful Product Information:

Material: Plastic		Style: Bar
Bar Cavities: 3		Bar Depth: 1.125"
Bar Width: 3"		Bar Length: 3"
Max Temperature: 135ºF		Mold Capacity (oz): 12.9
Avg. Bar Weight: 4.3 oz

RELATED PRODUCTS

Coast Guard Soap Mold (MW 557)

Army Soap Mold (MW 553)

Navy Soap Mold (MW 554)

Marines Soap Mold (MW 556)

International Nomenclature of Cosmetic Ingredients (INCI):
This product does not need to be listed on the product ingredient label.

Common Name Ingredient Listing (FDA Approved):
This product does not need to be listed on the product ingredient label.

Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.

Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.

Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.

Bath Fizzies: Tightly pack bath fizzy mixture into each mold cavity. Allow to harden and dry. (For best results, leave in mold overnight). Flip mold over onto clean surface and gently push bath fizzies out of mold.

Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.

Megan • Maryland

Date Submitted: 07/22/2019

I Recommend This Product!

	"Great details."
COMMENTS: These were a hit for an Air Force Academy graduation party! I love the detail in them.
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process

YTS • Texas

Date Submitted: 02/27/2018

I Recommend This Product!

	"personalize for the military personnel or veterans"
COMMENTS: Nice to give handmade products to people serving in the military and veterans.
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process, Soap - CPOP, Soap - Hot Process, Soap - Shampoo Bars, Soap - Shave Shampoo, Bath Fizzies & Salts, Body Sprays & Perfume, Exfoliants & Sugar Scrubs, Lotion Bars & Sticks

Karen • Washington

Date Submitted: 01/29/2018

"Great design BUT......."

COMMENTS: Was so excited to get this mold for my grandsons Jr ROTC Air Force Party. Poured in the soap and it all started running to one side. Looked closely and one of the cavities was about 1/2” less deep than the others which of course made all of the melted soap run downhill. . Quickly propped it up to keep more soap from running out. Called customer service the next day and they were kind enough to Immediately ship out a replacement mold. Got the replacement and it was exactly the same way. I even went so far as to put a contractors level on my counter to make sure it was totally level and it was, which confirmed the molds both had defects. Didn’t call again about this problem as I just propped up both molds on the low ends because I only had 5 days to get all of the 43 soaps made, cured and packaged in time for the event. This must be a defect from the manufacturer. Not sure. But the ROTC loved the soaps.

PRODUCT USED IN: Soap - Melt & Pour

THINGS I LIKE		THINGS I'D LIKE TO CHANGE
• Size • Great for military functions		• designs & wording deeper to see better • Level mold

Leslie • Michigan

Date Submitted: 11/08/2017

"Not as I had hoped"

COMMENTS: I bought this mold when it was first released and was looking forward to having something special at my craft show on Veteran's Day. Unfortunately, as previously reviewed, the detailing was difficult to highlight. I used mica on melt and pour soap and it definitely doesn't look as I had hoped. I tried a brush, foam brush and finger painting but none worked to create a good product.

PRODUCT USED IN: Soap - Melt & Pour

THINGS I LIKE		THINGS I'D LIKE TO CHANGE
• Great way to honor our military		• Better detailing

Mariann • New York

Date Submitted: 10/01/2017

	"Detailing is very light"
COMMENTS: Tried several different methods to get this mold to "pop"- but the detailing/impression is so faint no matter what method I tried (opaque soap, light, dark, clear, dusted with mica etc)it didnt matter. I was hoping this would be a good item for the veterans and active duty that we support.
PRODUCT USED IN: Soap - Melt & Pour

Theresa • Tennessee

Date Submitted: 08/16/2017

I Recommend This Product!

"Love them!"

COMMENTS: Thank you so much for creating these! I will use these to make nice gifts for my military family and friends

PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process, Soap - Shampoo Bars, Soap - Shave Shampoo, Bath Fizzies & Salts

THINGS I LIKE		THINGS I'D LIKE TO CHANGE
• Everythin

By using this site you agree to our user agreement. Click here to review
Copyright © 2024 Crafter's Choice® is a registered trademark of Crafter’s Choice Brands LLC. All rights reserved