|
|
Baby Feet Soap Mold (MW 465) |
|
|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
This soap mold is one of our favorite baby shower themed molds! The heart shaped mold cavities each have two tiny feet on them that can be colored blue or pink to represent a little baby boy or girl.
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135-145 degrees F. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
|  | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI):
This product does not need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved):
This product does not need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
| Average Customer Rating: |
 |
(4 Reviews) |
|
Diana • Ohio
Date Submitted: 12/27/2018
I Recommend This Product!
|
|
"Cute" |
|
COMMENTS: Love it , but they get damaged easy. Wish they are silicon made.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Shape
|
|
• Durability
|
|
|
|
Irma • Virginia
Date Submitted: 02/01/2017
I Recommend This Product!
|
 |
"Cute little baby feet !" |
|
COMMENTS: Great mold makes nice sized soaps , easy to use, much easier to remove the finished soaps than most plastic molds.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
|
|
Sarah • Minnesota
Date Submitted: 12/12/2016
I Recommend This Product!
|
|
"Mold" |
|
COMMENTS: Great little mold. Wasn't sure about about using plastic molds since I usually use silicone, but these popped right after a bit of time in the freezer. The soap it makes is adorable.
|
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
|
|
Jodi • Maryland
Date Submitted: 11/14/2016
I Recommend This Product!
|
|
"baby feet mold" |
|
COMMENTS: Good quality item
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• good quality
|
|
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
1 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
