|
Bicycle Soap Mold (MW 53) |
|
|
|
Additional Information |
|
Directions & Ingredients |
|
SDS & Documents |
|
|
You can practically feel the wind in your hair with the carved Bicycle Soap Mold. Perfect for cleaning up after a long bike ride with family and friends.
Common Uses:
Melt & Pour Soap. Cold Process Soap.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135-145 degrees F. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
| | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI): This product does need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved): This product does need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Average Customer Rating: |
|
(12 Reviews) |
Lara • Georgia
Date Submitted: 09/06/2019
I Recommend This Product!
|
|
"Detailed Soaps" |
COMMENTS: This mold made some wonderful detailed hot process soaps for my business. People compliment them by saying how cute the soaps are!
Thank you!
|
PRODUCT USED IN: Soap - Hot Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Easy to use and clean
|
|
• Nothing!
|
|
|
Amanda • Michigan
Date Submitted: 06/07/2019
I Recommend This Product!
|
|
"SO CUTE" |
COMMENTS: I bought this to make a summer design or my Sweet Strawberry soap. Makes them look really cute! Mold works great, lots of possibilities. Seems sturdy.
|
PRODUCT USED IN: Soap - Melt & Pour
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Cute • Easy to use
|
|
|
|
|
Karen • Washington
Date Submitted: 02/06/2018
I Recommend This Product!
|
|
"LOVE THIS MOLD!" |
COMMENTS: I think I own each and every mold MILKY WAY makes. I love the size of the bars as well as the great details in each style. Ease of de-molding is great if you allow them to cool in the mold. If you are inpatient like me, you can easily speed up the process by putting the mold in the refrigerator for about 15 - 20 minutes. The perfect design for people who ride bikes, no matter what their age.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Lucinda • Indiana
Date Submitted: 04/28/2017
I Recommend This Product!
|
|
"Specialty soap" |
COMMENTS: I bought this mold just to make soap for my daughter who loves biking. I know she'll love it as well as many of my customers.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
ERIKA • Florida
Date Submitted: 02/07/2017
I Recommend This Product!
|
|
"Nice design" |
COMMENTS: Nice design, unisex
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
nancy • Arizona
Date Submitted: 01/03/2017
I Recommend This Product!
|
|
"Bicycle Mold" |
COMMENTS: People love this mold especially for those bicyclist enthusiastics
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Design
|
|
• Nothing
|
|
|
Diane • Missouri
Date Submitted: 09/29/2016
|
|
"Not so great." |
COMMENTS: Never works for me.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
anabanana • California
Date Submitted: 08/10/2016
I Recommend This Product!
|
|
"LOVE, LOVE, LOVE" |
COMMENTS: We are avid cyclists, so this mold was an obvious choice. I love the molds I purchased! You must put your soap into the freezer after 24 hours of curing to get the soap out without disfiguring the shape. I suggest at least 15 minutes. For soft oil soaps, I suggest not much more time than the 15 minutes otherwise, you get the soap out but face the same possibility of disfiguring the soap due to the added "moisture" of the freezer and the softness of the oils used in CP.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Marissa • Wisconsin
Date Submitted: 07/18/2016
I Recommend This Product!
|
|
"Nice mold" |
COMMENTS: This is a super cute mold and I love the way the soap comes out, although after only a few uses the plastic mold gets a little messed up from releasing your soaps from the mold. I'd love if this came in a silicone mold.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Stephanie • Utah
Date Submitted: 02/14/2016
I Recommend This Product!
|
|
"Perfect for those of us who bike" |
COMMENTS: This mold is so perfect for the products I make for my boys. They all love to bike and the soaps and lotion bars that I give them from this mold make them feel special. I read a few reviews talking about ways to get the molds to easily release and here's what has worked for me; I spray a small amount of cooking spray into the cavity and really rub it into the small spaces of the spokes and seat before I pour the CP soap. Then after 24 hours I pop the mold with the soaps into the freezer for about 30 minutes. With gentle pressure they come right out, super crisp. It's my favorite mold.
|
PRODUCT USED IN: Soap - Cold Process, Lotion Bars & Sticks
|
|
|
Shannon • California
Date Submitted: 04/12/2015
I Recommend This Product!
|
|
"Very cute!" |
COMMENTS: Very cute and fun. I'm happy I added this to my collection.
|
PRODUCT USED IN: Soap - Melt & Pour
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• chic
|
|
|
|
|
Hayna • New York
Date Submitted: 04/05/2014
I Recommend This Product!
|
|
"Great size, fun graphic" |
COMMENTS: This mold has been a great addition to my soap and lotion making. The image comes out clean and soap and lotion release easily.
|
PRODUCT USED IN: Lotion Bars & Sticks
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
|
|
• Four cavities instead of three
|
|
|
Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
|
2 Question(s) Shown Below |
Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|