|
Dragon Soap Mold (MW 204) |
|
|
|
Additional Information |
|
Directions & Ingredients |
|
SDS & Documents |
|
|
This magnificent, mystical dragon is curled in a cave and ready to smoke anyone in his way. Our beautifully detailed Dragon soap mold is perfect for fantasy and Tolkien fans.
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135-145 degrees F. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
| | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI): This product does not need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved): This product does not need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Average Customer Rating: |
|
(6 Reviews) |
Melissa • Alabama
Date Submitted: 05/22/2017
I Recommend This Product!
|
|
"Love this mold!" |
COMMENTS: I have used this mold a lot. In fact, I own about 8 of them! Detail is very nice, unmolds easily, bars are of a good size (approximately 4 ounces). Customers really like them.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Easily Unmolds • Unique • Nice Detail
|
|
|
|
|
Robert • Massachusetts
Date Submitted: 04/08/2017
I Recommend This Product!
|
|
"??" |
COMMENTS: I use this for my Dragons Blood bath bomb and love it. Takes some practice but well worth it!
|
PRODUCT USED IN: Bath Fizzies & Salts
|
|
|
Eleanor • Utah
Date Submitted: 04/01/2017
I Recommend This Product!
|
|
"Nice design and soap pops out of the mold easily" |
COMMENTS: I have used this half-circle dragon mold a few times now, and people always gravitate to the soaps. The design isn't deep, but it's attractive and, after about 30 minutes in the freezer (I grease all my plastic molds with a fine layer of mineral oil), the soaps pop right out easily and perfect!
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• easy soap removal • the look of it
|
|
|
|
|
Pamela • Florida
Date Submitted: 03/28/2017
I Recommend This Product!
|
|
"Beautiful design" |
COMMENTS: I love this mold! The sized it perfect and the design is so beautiful. It is plastic but releases nicely.
|
PRODUCT USED IN: Soap - Melt & Pour
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• design
|
|
|
|
|
Pat • Virginia
Date Submitted: 10/21/2016
I Recommend This Product!
|
|
"Love the dragon!" |
COMMENTS: I use this dragon for both soaps and bath bombs. This is my favorite mold and sells very well for me, especially when using "dragony" scents in it. Plan to order more on my next order.
|
PRODUCT USED IN: Soap - Cold Process, Bath Fizzies & Salts
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• It's a dragon!
|
|
|
|
|
Mary • California
Date Submitted: 03/05/2016
I Recommend This Product!
|
|
"Milky Way™ Dragon Soap Mold (MW 204)" |
COMMENTS: It's a nice mold. A bit hard to see the shape of the dragon though. I like the other dragon shape better, but the open molds tend to warp after repeated use.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
|
0 Question(s) Shown Below |
Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|