|
Flowers Guest Soap Mold (MW 45) |
|
|
|
Additional Information |
|
Directions & Ingredients |
|
SDS & Documents |
|
|
There's no need to choose a favorite stylized flower design, because the Guest Flowers Soap Mold offers five lovely options, including some with hearts and waves.
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135ºF to145ºF. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
| | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI): This product does need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved): This product does need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Average Customer Rating: |
|
(11 Reviews) |
Karen • Utah
Date Submitted: 07/22/2017
I Recommend This Product!
|
|
"Flowers guest mold" |
COMMENTS: These are the perfect size for lotion bars, very easy to remove from mold.
|
PRODUCT USED IN: Bath Fizzies & Salts, Lotion Bars & Sticks
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• size • ease of removing
|
|
|
|
|
Elisabeth • Missouri
Date Submitted: 06/09/2017
I Recommend This Product!
|
|
"Very Nice" |
COMMENTS: This mold is really nice and easy to use. Very sturdy
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Christine • Illinois
Date Submitted: 12/29/2016
I Recommend This Product!
|
|
"Great for Lotion Bars " |
COMMENTS: I love making lotions bars with these! Just can't fill them all the way or they won't fit in their containers!
|
PRODUCT USED IN: Lotion Bars & Sticks
|
|
|
Sabrina • Kansas
Date Submitted: 12/09/2016
I Recommend This Product!
|
|
"Works great" |
COMMENTS: Works great. I mainly use to give that decorative touch to lotion bars.
|
PRODUCT USED IN: Lotion Bars & Sticks
|
|
|
jennifer • New Jersey
Date Submitted: 08/10/2016
I Recommend This Product!
|
|
"my favorite mold!" |
COMMENTS: I got this mold in the vanilla lotion bar kit and have purchased other ones since but this is the one I use the most. I like the different designs in the mold and the lotion bars come out very easily after leaving in freezer for about 20 minutes. I would recommend this mold.
|
PRODUCT USED IN: Lotion Bars & Sticks
|
|
|
Ruth • Maryland
Date Submitted: 05/06/2016
|
|
"Not easy to unmold" |
COMMENTS: Needed them to make favors. Really difficult to unmold. I'll use them again but not thrilled. If anyone has a clue to making the unmolding easier I would appreciate the advise.
CC Response: | For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold. |
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Carrie • Florida
Date Submitted: 05/22/2015
I Recommend This Product!
|
|
"Great guest soaps!" |
COMMENTS: Makes lovely lotion bars too that fit nicely in the 2 ounce lidded tins. Cute designs -everyone seems to like them
|
PRODUCT USED IN: Soap - Melt & Pour, Lotion Bars & Sticks
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Cute • Versatile • Easy to use and release
|
|
|
|
|
Jamie • Arizona
Date Submitted: 04/23/2015
I Recommend This Product!
|
|
"Great Detail" |
COMMENTS: I used this mold for the first time with lotion bars and they came out beautiful and the detail is very nice on each one. I allowed them to set for several hours came back and they just popped right out of the mold.
|
PRODUCT USED IN: Soap - Melt & Pour, Lotion Bars & Sticks
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Detail
|
|
|
|
|
veronica • Texas
Date Submitted: 02/08/2015
I Recommend This Product!
|
|
"highly recomend " |
COMMENTS: I used this mold for my lotion bars. I was worried they would not come out very easy. Lol all I had to do is turn the mold over and they fell right out. Love this mold.
|
PRODUCT USED IN: Lotion Bars & Sticks
|
|
|
Jecci • Ohio
Date Submitted: 10/28/2014
I Recommend This Product!
|
|
"Love these molds!" |
COMMENTS: These are great to make lotion bars. So easy to unmold and such pretty designs.
|
PRODUCT USED IN: Lotion Bars & Sticks
|
|
|
Christina • Kansas
Date Submitted: 03/27/2014
I Recommend This Product!
|
|
"Pop out easily" |
COMMENTS: The MP soaps popped out easily. No air bubbles or missing mold areas.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
|
4 Question(s) Shown Below |
Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|