|
|
Big Tray - Handmade Soap Mold (MW 144) |
|
|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
Got a big batch of homemade soap ready to go? The Handmade Soap Mold Tray will make sixteen rectangle soap bars, each with the word "Handmade" stamped across the top with a floral border.
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135-145 degrees F. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
|  | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI):
This product does not need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved):
This product does not need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold, and slice into bars. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Slice into bars. Allow soap to cure for 4-8 weeks. Note that some cp soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold. Slice into lotion bars.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
| Average Customer Rating: |
 |
(8 Reviews) |
|
stacey • Michigan
Date Submitted: 06/26/2017
I Recommend This Product!
|
|
"its ok" |
|
COMMENTS: not sure i like the look of it
|
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
|
|
Julie • Virginia
Date Submitted: 01/12/2017
I Recommend This Product!
|
 |
"mold" |
|
COMMENTS: good size
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• size
• graphic
|
|
|
|
|
|
LaShon • Virginia
Date Submitted: 12/17/2016
I Recommend This Product!
|
|
"Great product" |
|
COMMENTS: The mold was very helpful when I need a large batch already pre-lined for cutting. I like that it has handmade engraved in the mold.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
|
|
Jennifer • New York
Date Submitted: 11/30/2016
I Recommend This Product!
|
|
"love it " |
|
COMMENTS: I love this mold, t is very easy to use. It takes only a few seconds to unmold it. It is also easy to cut the soaps once you unmold it because of the lines in between each bar.
|
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
|
|
Jenia • South Carolina
Date Submitted: 11/08/2016
|
 |
"Nice but needs to be silicone" |
|
COMMENTS: Beautiful but needs to be offered in silicone. Extremely hard unmolding if u do not grease beforehand ! Needs to be more flexible plastic!
|
|
PRODUCT USED IN: Soap - Hot Process
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Pretty & cheap
|
|
• Make more sturdy
• Make a silicone mold of it
|
|
|
|
Tisa • Ohio
Date Submitted: 05/03/2016
|
 |
"Huge! " |
|
COMMENTS: Whoa. This mold is huge. If you want big chucky bars of soap this is the mold for you.
I was not expecting it to be so big and deep. Prepare to have alot of melt and pour ready to fill it. I used it in a Gardener's Soap and Layered it. Turned out great. Not sure how often I will use this as it takes up alot of soap.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
|
|
Reva • Arizona
Date Submitted: 11/02/2014
I Recommend This Product!
|
|
"The Best Ever!" |
|
COMMENTS: My customers love the size of this bar. I overpour them and usually can get them close to 6 ounces which is awesome and more bang for their buck. I wish they sold this same size Goats Milk version.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
|
|
Gables Apartment • Florida
Date Submitted: 07/29/2014
I Recommend This Product!
|
|
"Very cute bars." |
|
COMMENTS: You can make them thick or thin depending on the size bar that you want. I used gloves to shower so when I rubbed this bar of soap against the front part of it, the Handmade and accents disappeared altogether - which is fine, it was bound to go away anyways. Easy to pop out, which I liked.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Huge!
|
|
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
4 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
