|
|
Nautical Soap Mold (MW 122) |
|
|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
Take the helm with this set of oceanic soap shapes, sure to be a hit with land lubbers and sea farers alike. The Nautical Soap Mold features an anchor, a compass, and a ship's wheel.
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Manufacturer: Milky Way Molds
Material: Clear PVC Plastic (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135ºF to145ºF. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
|  | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI):
This product does not need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved):
This product does not need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
| Average Customer Rating: |
 |
(6 Reviews) |
|
Pamela • Pennsylvania
Date Submitted: 05/17/2021
I Recommend This Product!
|
|
"Nautical Soap Mold" |
|
COMMENTS: I use Milky Way Soap Molds for all of my Melt & Pour Bases. I will even use these for excess when making Cold Process Soap. (If needed will refrigerate for a bit to help with the releasing.). Overall very satisfied!
|
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process, Soap - Shave Shampoo
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Variety of designs!
|
|
• Nothing!
|
|
|
|
Brooke • Florida
Date Submitted: 02/05/2021
I Recommend This Product!
|
 |
"Pretty good. " |
|
COMMENTS: LOVE the anchor. I can’t use the Compass because the design is too big for the mold & you only get partials of the letters. Wish a mold with all Anchors were available.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Anchor
|
|
• Compass
|
|
|
|
Robin • Florida
Date Submitted: 05/28/2017
I Recommend This Product!
|
|
"Guys like these" |
|
COMMENTS: I use these molds for the men's shaving soaps. Fun nautical theme, look great and fit nicely into shaving mugs.
|
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Shave Shampoo
|
|
|
|
|
Shannon • Maine
Date Submitted: 03/18/2016
I Recommend This Product!
|
|
"Love these!" |
|
COMMENTS: LOVE THESE! Perfect for my nautical themed soap line, I just love these shapes. I have bought about 15 of them! Great mold, holds up over time and is super cute. Thanks!
|
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
|
|
Shannon • California
Date Submitted: 07/15/2015
I Recommend This Product!
|
|
"Quality" |
|
COMMENTS: Very good size and great quality.
|
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process
|
|
|
|
|
Joanne • Florida
Date Submitted: 07/29/2014
I Recommend This Product!
|
|
"Great!" |
|
COMMENTS: We love using this mold for soaps and bath bombs. Great size and easy to use.
|
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process, Bath Fizzies & Salts
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
|
|
• Add an additional mold making it 4
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
0 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
