|
Long Loaf Silicone Soap Mold 1503 |
|
|
|
Additional Information |
|
Directions & Ingredients |
|
SDS & Documents |
|
|
This is a thick and sturdy silicone loaf mold that weighs nearly 3 lb. on its own. Originally designed to fit as a liner in the Crafter's Choice Wooden Long Loaf Soap Mold (discontinued) or you can use it as a stand alone mold, but will need to support the sides from bowing. The natural color silicone is 1/4" thick on all sides.
Loaf Dimensions: 3 1/8" wide x 19 15/16" long x 3 1/8" deep
Country Of Origin: China
| | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI): This product does need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved): This product does need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap into silicone mold. Allow soap to cool at room temperature until hard. Carefully remove loaf from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the loaf and carefully pull out of the mold. Slice into bars.
Cold Process Soap: Pour soap at trace into mold. After at least 24 hours, gently pull silicone mold to loosen its grip on the soap. Flip mold over onto a clean surface or cookie sheet and gently push on the bottom of mold until the soap starts to release. Grab hold of the loaf with a gloved hand. Slice into bars and allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Cold Process/Oven Process Soap: Pour soap at trace into the mold. Preheat oven to 170ºF then place mold in oven. Turn oven off, and keep soap in oven overnight. The next day remove mold from oven. Carefully remove loaf from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Slice into bars, and allow soap to cure for 2 to 4 weeks.
Hot Process Soap: Scoop hot process soap into mold. Gently tap the mold onto the counter to remove air pockets. Allow soap to cool and harden. (This can take up to 48 hours.) Carefully remove loaf from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the loaf and carefully pull out of mold. Slice into bars.
Care: Hand wash mold in warm, sudsy water.
Average Customer Rating: |
|
(32 Reviews) |
Victoria • Ohio
Date Submitted: 11/21/2018
I Recommend This Product!
|
|
"Long Loaf Silicone Soap Mold" |
COMMENTS: I love this mold it is very sturdy. You will need wood mold or something to keep the middle from bowing out, but I just used some scrap wood and made a box to fit over it and it works perfectly. It holds more soap batter than a 5 pound mold I have, which is fine. My soaps come out smooth and so easy. You won't be disappointed! I use this mold for my cold process soaps.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• How thick this mold is
|
|
• Nothing
|
|
|
Deirdre • Illinois
Date Submitted: 10/31/2018
I Recommend This Product!
|
|
"Great Size, Reds to be thinner!" |
COMMENTS: Nice size and dimensions. I just wish the liner was a bit thinner. It’s somewhat difficult to unfold the soaps...
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process
|
|
|
Lisa • New Mexico
Date Submitted: 10/12/2018
I Recommend This Product!
|
|
"Long Loaf Silicon Mold " |
COMMENTS: I love this mold and how easily my soaps come out of it. The mold is very sturdy for silicon and is so smooth there is no waste on the ends. The bars are just as smooth on the ends as the cuts. The mold just makes me happy every time I use it! I will be buying more soon!
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Audrey • Texas
Date Submitted: 06/13/2018
I Recommend This Product!
|
|
"Excellent Mold" |
COMMENTS: I've been using these molds for a couple of years and they are my favorite. They work great and hold up to both my CP and HP soaps. I toss them in the freezer for an hour or two to help unmold my softer soaps and have had no issues at all. I only wish they made a tall and skinny version and then I'd be beyond happy! I have several of these and one seems to want to fold in a little, so I add a couple pieces of tape to keep it against my wooden mold and my soaps don't warp. Other than that, there's no prep involved with these. No more freezer paper!
|
PRODUCT USED IN: Soap - Cold Process, Soap - Hot Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Flexible • Long lasting
|
|
|
|
|
Hartence • New Jersey
Date Submitted: 09/01/2017
I Recommend This Product!
|
|
"Best silicone mold" |
COMMENTS: This is the biggest silicone mold that I own. It is perfect when you want to go to the next level, to increase your production with less effort. It releases great! The soaps are beautiful and professional looking.
|
PRODUCT USED IN: Soap - Melt & Pour
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• The size • Easy release
|
|
|
|
|
kristi • North Dakota
Date Submitted: 08/15/2017
I Recommend This Product!
|
|
"love" |
COMMENTS: perfect for my soap
|
PRODUCT USED IN: Soap - Hot Process
|
|
|
Sherry • Florida
Date Submitted: 07/20/2017
I Recommend This Product!
|
|
"It's a Giant!" |
COMMENTS: It's big, but glad it fits in my refrigerator. Keep the box that it arrives in for a little stability. It's pretty substantial on it's own!
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Debbie • Georgia
Date Submitted: 06/01/2017
I Recommend This Product!
|
|
"Love it!" |
COMMENTS: Perfect for making my soap bars! Love how easy it is to use.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Annette • Connecticut
Date Submitted: 03/05/2017
I Recommend This Product!
|
|
"silicone soap mold" |
COMMENTS: works great used for hot process soap can out very easy
|
PRODUCT USED IN: Soap - Hot Process
|
|
|
Mariya • Wisconsin
Date Submitted: 10/25/2016
I Recommend This Product!
|
|
"Love it! " |
COMMENTS: Amazing silicone mold. My soap came out super easy.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Darlene • New York
Date Submitted: 09/19/2016
I Recommend This Product!
|
|
"Love!" |
COMMENTS: I love this mold and it is wonderful to work with and clean
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process
|
|
|
Lynnsy • Colorado
Date Submitted: 09/05/2016
I Recommend This Product!
|
|
"My go-to molds" |
COMMENTS: I own 6 of these and these are my standard go-to molds for most of my soap making. I have slab molds and other small tester molds but these are by far my most used molds. They are a little tricky to unmold CP soap from if you aren't using steric acid as you can lose some corners but I freeze my soaps for a couple hours before unmolding to avoid the issue.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Amy • Virginia
Date Submitted: 05/17/2016
I Recommend This Product!
|
|
"Upgrade from hobby to business" |
COMMENTS: I appreciate the ability of the product to perform as expected. The interior is smooth and has sharp edges. My soap was easy to unmold. Cuts my soap making time in half for the sheer amount it makes. Great investment.
|
PRODUCT USED IN: Soap - CPOP
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• 20 one ince bars!
|
|
|
|
|
Amanda • California
Date Submitted: 04/29/2016
I Recommend This Product!
|
|
"So easy" |
COMMENTS: I love this mold. Soap releases so easy.
|
PRODUCT USED IN: Soap - Melt & Pour
|
|
|
Patricia • Colorado
Date Submitted: 04/08/2016
I Recommend This Product!
|
|
"Love this Mold - Wish they would adjust slightly" |
COMMENTS: This mold is outstanding and plan to order a few more. Only issue I find is that I always end up with a smaller slice at the end - wish it was 1" longer.
I have been spraying this mold with "Pam" - spray of oil and coat the mold well prior to placing my Cold Process soup inside. It works like a charm - I never have a problem releasing the soap from the mold after I started this process.
I also find that that when this mold is within a wooden frame that I don't need to cover to cure. It gets too hot and my soap cracks or seems to semi-gel. I began to just leave it on a drying rack and I've had much better soap results.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Cold Process
|
|
• Make 1" longer
|
|
|
Kim • Colorado
Date Submitted: 11/16/2015
I Recommend This Product!
|
|
"Dimensions have changed! Mold is shorter!" |
COMMENTS: This is the best mold I've ever used. So easy to release the soap, and so easy to clean. So I bought additional molds a couple of months ago and was disappointed to see the length is slightly shorter than the molds I had previously bought. There is a definite gap on the one side of the mold, whereas my older molds had a snug fit inside the wooden mold. My older molds used to make 20x 1 inch bars, but now I can only get 19x 1 inch bars and am left with a skinny end piece! A bit disappointed.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Easy to release the soap • Easy to clean • Love the side slots
|
|
• Make it 1/4 inch longer like it was b4
|
|
|
YTS • Texas
Date Submitted: 11/13/2015
I Recommend This Product!
|
|
"I love it!!!" |
COMMENTS: Amazing liner along with the wood mold!
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Jane • New Mexico
Date Submitted: 09/05/2015
I Recommend This Product!
|
|
"Dream mold does the job" |
COMMENTS: I love this mold. It makes such a nice, large, approximately, 6 lb loaf of soap. I don't have the wooden mold but used the box that it came in to support the mold. I reinforced the box with duct tape and it is working beautifully. I hope to be able to purchase more of these wonderful molds.
|
PRODUCT USED IN: Soap - Melt & Pour
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Ease of use and that I can get 18 bars
|
|
• wish it weren't so pricey.
|
|
|
Jorge • Florida
Date Submitted: 06/29/2015
I Recommend This Product!
|
|
"Easy to use" |
COMMENTS: It's easy to use and clean but it's necessary use the wood mold because without it gets no uniform soap.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Easy to handle
|
|
|
|
|
Janice • California
Date Submitted: 06/24/2015
I Recommend This Product!
|
|
"Perfect!!" |
COMMENTS: I bought this when the sale was going on and it is a perfect size, the first batch I made was too big had a lot left over. I did 2400 grams. The next one I will try 2000 grams. Great quality.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Quality • Thickness
|
|
• none
|
|
|
jennifer • California
Date Submitted: 04/27/2015
I Recommend This Product!
|
|
"A staple loaf" |
COMMENTS: It's a little pricier than some others but I've realized it's worth it for the ease of use and how sturdy it is. It definitely pays for itself after a few batches with the size it makes. I plan to buy a few more and make it a staple for my soaps. With the silicone insert my bars are the perfect size and they always CPOP perfectly.
|
PRODUCT USED IN: Soap - Cold Process, Soap - CPOP
|
|
|
Karen • Nebraska
Date Submitted: 03/20/2015
I Recommend This Product!
|
|
"Long Loaf Silicone Soap Mold" |
COMMENTS: I love this mold. I've been using an 11-bar silicone mold, and wanted one that was larger. The soap released so easily from this mold. I'm using the cardboard box it came in when it's curing until I save up for the wooden part. I plan to buy more.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Size • Easy of soap removal
|
|
|
|
|
sylvie • New Jersey
Date Submitted: 03/08/2015
I Recommend This Product!
|
|
"Soap Mold" |
COMMENTS: Great mold, makes unmolding easy. Definitely need the wood box to stabilize the center.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Sonja • Michigan
Date Submitted: 02/27/2015
I Recommend This Product!
|
|
"Great quality" |
COMMENTS: Super sturdy, great quality liner. Soap comes out nicely. However, the size of the liner and thickness of the silicone is such that my bars end up narrower than I prefer. If you like the size, you will love it.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Laura • Ohio
Date Submitted: 02/03/2015
I Recommend This Product!
|
|
"Exactly what we needed!" |
COMMENTS: These silicon molds are perfect for our soap business! We were using molds that would only yield 12 bars, these give us 18 in almost the same size, so customers shouldn't notice a huge change. The soap pops right out! Please don't ever quit selling them, we may need to add more! Will be interesting to see what the life expectancy ends up being, but I'm confident they will last us a long time.
|
PRODUCT USED IN: Soap - Cold Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• soap pops right out • easy cleanup for next use
|
|
|
|
|
Barbara • Ohio
Date Submitted: 11/22/2014
I Recommend This Product!
|
|
"Love my new molds!!" |
COMMENTS: I really enjoyed using this and not having to line it with paper first! Unmolded super easy and cleans up well too.
|
PRODUCT USED IN: Soap - Cold Process, Soap - CPOP
|
|
|
Janet • North Carolina
Date Submitted: 10/04/2014
I Recommend This Product!
|
|
"Love it!!" |
COMMENTS: I have just started soaping and this makes it so much easier for me. In fact, the box that it was shipped in is a good enough outer mold for me until I can afford a wooden mold. Love that I can make a large batch in one mold.
|
PRODUCT USED IN: Soap - Hot Process
|
|
|
Jennifer • Illinois
Date Submitted: 08/23/2014
I Recommend This Product!
|
|
"Wonderful" |
COMMENTS: love this mold use them every day !!!
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process
|
|
|
Peggy • New York
Date Submitted: 08/03/2014
I Recommend This Product!
|
|
"Soap making is now more enjoyable" |
COMMENTS: Truly love this mold, ordering 5 more to increase my soap making on a daily basis. So easy to get the soap out of the molds.
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Marcellette • Michigan
Date Submitted: 03/01/2014
I Recommend This Product!
|
|
"Long Silicone Loaf Soap Mold" |
COMMENTS: Just purchased this mold made HP & CP, soap easy to remove for mold love it!!! I will purchase more,
|
PRODUCT USED IN: Soap - Cold Process, Soap - Hot Process
|
|
|
Deborah • North Carolina
Date Submitted: 01/11/2014
I Recommend This Product!
|
|
"Love, Love, Love this loaf mold!" |
COMMENTS: OMG, I would have bunches of these if they weren't so darn expensive! I absolutely LOVE it! I had planned on having my husband build me a wood mold for this liner if the sides didn't stand straight on their own, but it's pretty thick. I do think the sides would bow if no support is there just because of the length of the thing, but with a little packing tape for reinforcement the box it comes in works just fine! I made six pounds of soap because the description said the mold holds about 6.5 lbs of water, but about 5.5 lbs of soap batter filled mine nicely.
|
PRODUCT USED IN: Soap - Cold Process, Soap - Hot Process
|
THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Not having to make a liner!
|
|
• Make it less expensive!
|
|
|
Kristina • California
Date Submitted: 12/31/2013
I Recommend This Product!
|
|
"I love this mold" |
COMMENTS: I love how long and tall this mold is. I initially purchased the wood mold, which I love. When this liner came out I ordered it. I love how sturdy it is, the walls and bottom are very thick, it is easy to unmold and perfect for tall bars of soap. I wish the price was little lower, but for me, I just wait until there is a sale or I have saved enough in reward points and then I splurge. If you like tall bars then this mold is perfect. It is built to last!
|
PRODUCT USED IN: Soap - Cold Process
|
|
|
Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
|
17 Question(s) Shown Below |
Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|